Abstract The aim of this research was to evaluate age-related changes in the smile of Brazilian women. The sample consisted of 249 Brazilian women who had not undergone previous orthodontic treatment or facial surgery. They were divided into four groups, according to age: G1 (20-29), G2 (30-39), G3 (40-49) and G4 (50 or older). Standardized front view photographs were taken while smiling and at rest. Measurements were evaluated by ANOVA and post-hoc Tukey. The Chi-square test was applied for qualitative variables. Upper lip thickness at rest and exposure of upper incisors on smiling decreased with age. Most individuals (60.9%) exhibited a medium smile. High smiles were more often seen in G1 (45%) and less frequently in G4 (18.8%), whereas the opposite occurred with the low smile, i.e., G4 (21.9%) and G1 (6.7%). Variations among the groups were observed in the transverse exposure of the teeth on smiling. In G1 and G3, there was a balance between tooth exposures, so that the teeth were exposed as far as the premolars and/or molars. Most of the women (56.3%) in G2 exposed their teeth as far as the first molars on smiling, whereas most of those (40.6%) in G4 exposed their teeth only as far as the first premolars on smiling. As age increased, there was decreased exposure of the upper incisors, decreased upper lip thickness and lower exposure of teeth vertically and transversely.

The purpose of the present study was to assess the association between overbite and craniofacial growth pattern. The sample comprised eighty-six cephalograms obtained during the orthodontic pretreatment phase and analyzed using the Radiocef program to identify the craniofacial landmarks and perform orthodontic measurements. The variables utilized were overbite, the Jarabak percentage and the Vert index, as well as classifications resulting from the interpretation of these measurements. In all the statistical tests, a significance level of 5% was considered. Measurement reliability was checked by calculating method error. Weighted Kappa analysis showed that agreement between the facial types defined by the Vert index and the direction of growth trend established by the Jarabak percentage was not satisfactory. Owing to this lack of equivalency, a potential association between overbite and craniofacial growth pattern was evaluated using the chi-square test, considering the two methods separately. No relationship of dependence between overbite and craniofacial growth pattern was revealed by the results obtained. Therefore, it can be concluded that the classification of facial growth pattern will not be the same when considering the Jarabak and the Ricketts anayses, and that increased overbite cannot be associated with a braquifacial growth pattern, nor can openbite be associated with a dolichofacial growth pattern.

O presente estudo comparou as forças em arcos de intrusão com dobra V confeccionados em aço inoxidável, TiMolium® e TMA®, com diferentes magnitudes de deflexão. A amostra constou de fios de secção retangular e calibre 0,017" x 0,025", com dez arcos de cada liga. Todas as dobras em V foram confeccionadas a 48 mm distantes da linha média, e foi utilizado o mesmo manequim de maxila para manter a mesma distância entre os tubos fixados nos molares e a linha média. As cargas necessárias para defletir os arcos em 5, 10, 15 e 20 mm foram mensuradas por meio de dinamômetro com célula de carga de 1 kgf, da marca Instron. O cálculo para o tamanho de amostra confirmou a possibilidade de se utilizar dez arcos de cada liga. Os testes de variância (ANOVA) de um fator e três níveis, complementados com os testes de Tukey para comparações múltiplas, identificaram que os arcos de intrusão de TMA® requereram menor quantidade de carga em relação ao aço convencional e ao TiMolium® em todos os níveis de deflexão; que o TiMolium® apresentou características intermediárias entre o aço e o TMA®; que em todas as ligas o aumento das distâncias implicou em aumento significativo da força entre todos os valores registrados; e que os incrementos de carga necessários para defletir os arcos nos intervalos tenderam a decrescer do primeiro ao último intervalo, sendo essas diferenças mais significantes no aço, menores no TiMolium® e praticamente inexistentes no TMA®.

The present study compared forces in stainless steel, TiMolium® and TMA®, V-bend intrusion arches with different magnitudes of flexion. The sample consisted of rectangular-section wires, caliber .017" x .025", with ten arches of each alloy. All V-bends were made 48 mm from the midline, using the same phantom upper jaw, maintaining the same distance between the tubes fixed to the molars and the midline. Loads necessary to deflect the arches by 5, 10, 15 and 20 mm were measured by means of an Instron dynamometer with a 1 kgf load cell. Calculations for sample size confirmed the suitability of using 10 arches of each alloy. Variance tests (ANOVA) of one factor and three levels, complemented by the Tukey test for multiple comparisons, identified that TMA® intrusion arches required a smaller quantity of load in relation to conventional steel and TiMolium® at all levels of flexion. Furthermore, TiMolium® presented intermediary characteristics between steel and TMA®, and in all alloys increase in distance entailed a significant increase in force between all registered values, and that the increase in load necessary to deflect the arches at the intervals tended to decrease from first to last interval, these differences being more significant in steel, less in TiMolium® and practically non-existent in TMA®.

O presente estudo avaliou a correlação entre expansão transversal e aumento no perímetro do arco dentário superior, após disjunção maxilar, em dezoito pares de modelos de gesso, obtidos antes e depois de aproximadamente cinco meses da disjunção maxilar. Os modelos foram fotocopiados e as variáveis largura intermolares, largura intercaninos, comprimento e perímetro do arco dentário superior foram mensuradas por meio de paquímetro digital. Depois de verificado o erro do método, um modelo de regressão múltipla foi desenvolvido em seqüência à identificação do melhor conjunto de variáveis. A equação resultante permitiu concluir que o aumento no perímetro do arco é dado pela adição de 0,54 vezes a alteração intercaninos e de 0,87 vezes a alteração no comprimento do arco.

The purpose of the present study was to assess the correlation between transverse expansion and the increase in upper arch perimeter, after maxillary expansion. Dental casts of eighteen patients were obtained before treatment and again five months after maxillary expansion. Measurements of intermolar width, intercanine width, arch length and arch perimeter were made with a digital caliper on photocopies taken from the dental casts. After assessment of the method error, a multiple regression model was developed following the identification of the best subset of variables. The resulting equation led to the conclusion that the increase in arch perimeter is approximately given by the addition of 0.54 times the intercanine expansion, and 0.87 times the arch length alteration.